Skip to content

Services

Wind turbine blade services, inspection to restoration

Seven service lines covering the blade maintenance cycle. Each is delivered by technicians whose qualifications match the scope, working to the applicable repair procedures and your site requirements.

Service 01

Wind Turbine Blade Inspections

Inspection quality sets the accuracy of every decision that follows. DBS technicians carry out internal and external blade inspections to locate damage, record its extent and location by blade station, and give asset owners and engineering teams a clear basis for repair planning.

Findings are documented with annotated photographs, measurements and severity observations in a format agreed with the customer, so they can be compared across inspection campaigns and fed directly into repair scopes.

Capabilities

  • Internal blade inspections
  • External blade inspections
  • Damage identification and assessment
  • Structural condition evaluations
  • Lightning strike damage assessments
  • Leading-edge erosion inspections
  • Inspection documentation and reporting
Request a Quote
Service 02

Composite and Structural Blade Repairs

Composite blade repairs depend on correct damage removal, laminate preparation, ply sequencing, cure control and verification. DBS crews perform fiberglass and structural laminate repairs in line with the OEM or customer repair instruction that applies to the blade and damage category.

Each repair is recorded with materials, batch information, environmental conditions and before-and-after documentation, giving the customer a traceable repair record.

Capabilities

  • Fiberglass composite repairs
  • Structural laminate repairs
  • Stress crack repairs
  • Core material replacement
  • Internal and external structural restoration
  • Impact damage repair
  • Major blade repair support
Request a Quote
Service 03

Lightning Damage Repairs

Lightning strikes can cause damage that is not fully visible from the blade surface, including delamination, debonding and heat damage around receptors and conductors. DBS technicians assess the affected area, map the extent of damage and carry out surface and structural repairs within the approved repair scope.

Where findings exceed the authorized repair category, they are documented and escalated to the customer's engineering team before work proceeds.

Capabilities

  • Lightning strike damage assessment
  • Surface and structural damage repairs
  • Composite restoration
  • Flashover damage evaluation
  • Associated blade damage repair
Request a Quote
Service 04

Leading Edge Protection (LEP)

Leading-edge erosion reduces aerodynamic efficiency and, left untreated, exposes the laminate to further damage. DBS assesses erosion severity along the blade span and restores the leading edge before applying or repairing the specified protection system.

Surface preparation, product application and cure follow the manufacturer's system instructions and the customer's site conditions, with each blade's work recorded for future maintenance planning.

Capabilities

  • Leading-edge erosion assessment
  • Leading-edge restoration
  • LEP application and repair
  • Surface preparation
  • Blade protection maintenance
Request a Quote
Service 05

Rope Access and Blade Maintenance

Rope access gives crews direct reach to the blade surface with a small equipment footprint and short setup times. DBS deploys technicians who hold the rope access qualifications required by the customer and site, working under a written rescue plan and the site's work-at-height procedures.

The same crews can move between inspection, preventative maintenance and corrective repair, reducing the number of separate mobilizations needed to keep blades in service.

Capabilities

  • Rope access-supported blade inspections
  • Rope access-supported blade repair
  • Elevated maintenance operations
  • Preventative blade maintenance
  • Corrective maintenance support
Request a Quote
Service 06

Major Blade Repair and Restoration

Major blade repairs require planning, controlled working conditions and close coordination with the customer's engineering team. DBS supports these projects with experienced composite technicians who work to the engineering disposition and repair instruction issued for the blade.

Work can be delivered up-tower or on the ground, depending on the repair method, platform and access approach specified by the customer.

Capabilities

  • Complex structural repair projects
  • Extensive composite restoration
  • Core material replacement
  • Significant damage remediation
  • Project-specific technical repair solutions
Request a Quote
Service 07

Blade Upgrades and Modifications

Blade upgrade programs are most effective when installation quality is consistent across the fleet. DBS crews install approved upgrades and modifications to the supplier's instructions and the customer's work package.

Each installation is documented blade by blade, giving the asset owner a clear record of what was fitted, where and when.

Capabilities

  • Leading-edge protection upgrades
  • Approved blade modifications
  • Project-specific blade improvement work
  • Preventative maintenance upgrades
Request a Quote

Repair categories and platform approvals

The repair categories DBS performs on a given project depend on the turbine platform, the applicable OEM or customer repair instructions, and the qualifications of the assigned technicians. Scope, repair classification and any required approvals are confirmed with the customer before work begins. Listing a service here does not imply authorization for every turbine platform or repair classification.

Request for Quote

Planning blade work for an upcoming season?

Send us the scope, site and timing. We will review the requirement and respond with availability, crew approach and next steps.